Hessarghatta, Bangalore, Karnataka
Leading Manufacturers, Exporters and Wholesaler of Bobbin Heater, Bolt Heater, Chemical Immersion Heater, Coil Heater, Duct Heater with Flameproof Enclosure, Flameproof Enclosure Heater, Flexible Tubular Heater, Heater Bank, High Density Cartridge Heater, Immersion Heater with Flange, Teflon Coated Heater and Tubular Heater from Bangalore.
Business Type | Manufacturer, Supplier |
Element Wire Material | Nichrome |
Heater Sizes | 0 25,30,35,42 mm |
Type of Termination | Threaded, Cable |
Sheaths | SS 304, 55 316, 55 310, Inconel 800, Titanium |
Maximum Temperature | 300 Degree Centigrade |
Volatge | 120, 230, 415 V |
Preferred Buyer From
Location | Worldwide |
Bobbin type heaters are used with an external pipes usually for oil and gas heating, the main advantage is easy replacement and very efficient. The heating element is supported by the refractory bobbins. Bobbin heaters are also supplied with protection tubes.
Business Type | Manufacturer, Supplier |
Element Wire Material | Nichrome |
Surface Wattage | 70 Whiz |
Standard Sizes | 0 8,10,12,14,16,19,22,25 mm |
Type of Termination | Cable |
Connectors | Industrial Sockets or Special Connectors from Amphenol Connectors (on Request) |
Sheaths | SS 304, Inconel 600, Inconel 800 |
Standard Voltages | 120, 230, 415 V(On as per Customers Requirement) |
Preferred Buyer From
Location | Worldwide |
Bolt heaters are used to tighten large bolts in many applications. The shaft of the heater is inserted into the hollow bolt and then its heated to expand it, allowing further tightening of the nuts.
Available in several dimensions and length to fit the requirement can be customized as per your size, hot zone and cold zone is also customized as per your requirement.
Heatcon bolt heater element lends itself to virtually the entire range of below applications:-
Pressure vessels Turbines Die blocks Cylinder heads Pressure vessels Compressors
Business Type | Manufacturer, Supplier |
Material | Nichrome, Kanthal |
Surface Wattage | 20-25 W/In2 |
Heater Tube Sizes | 0 8,11,14 Mm (Tubular) 25,30,50,60,80mm (Pipe/cartridge Type) |
Grade of Protection for Enclosure | IO 55,IP 65,IP 67, Atex, Ccoe, Flameproof, STD |
Type of Termination | Threaded, Cable |
Connectors | Industrial Sockets or Special Connectors from Amphenol Connectors On Request |
Sheaths | SS 304,55 316,Titanium, Silica, Quartz |
Preferred Buyer From
Location | Worldwide |
Heatcon chemical immersion heaters are used for heating highly corrosive liquids and chemicals, the entire range of below applications:-
Business Type | Manufacturer, Supplier |
Applications | Heating of Manifolds, Heating of Nozzles, Heating of Sealed Heads in Packing |
Standard Dimensions | 1.0*1.6mm, 1.3*2.3mm, 1.8*3,.2mm, 2.2*4.2mm, , 3.0*3.0mm, 4,.6*8.6mm |
Connection Options | PTFE insulated leads, Glass-silk NI leads, Ground wire |
Sheath | SS & Nickel |
Exit Options | Axial, Radial, in the Mid, Tangential |
General Options | Straight, Reflection Tube, Casted in Brass |
Clamping Options | Tangential Screw Clamping Band, Axial Screw Clamping Band, Lock-system |
Preferred Buyer From
Location | Worldwide |
The coil heaters coil heaters have maximum surface load and come with an IP rating for humidity-resistant coil heaters.
Business Type | Manufacturer, Supplier |
Element Wire Material | Nichrome |
Surface Wattage | 41 - 47 W/In2 |
Heater Tube Sizes | 0 8,11,14 mm |
Grade of Protection for Enclosure | STD fabricated or FLAMEPROOF (on request) |
Type of Termination | Threaded , Cable |
Connectors | Industrial Sockets or Special Connectors from Amphenol Connectors On Request |
Sheaths | SS 304, SS316, SS 310 Inconel 800 |
Heater Type | With Fins & Without Fins (tubular) |
Heater Mounting | Thread Mounted On Flange Plate |
Control | Thermostat, SSR, Thyristor, BMS, Contactor, Air Pressure Switch |
Wattage | Upto 1500 Kw |
Voltage | 120, 230, 415 V |
Preferred Buyer From
Location | Worldwide |
Heatcon Duct heaters can be easily mounted on to the duct with flange, which allows easy installation. There is an inbuilt thermostat which prevents over heating and insulation to avoid heat loss theversatile and economical tubular heating element lends itself to virtually the entire range of below applications:
Business Type | Manufacturer, Supplier |
Length | 20-30 Inch |
Frequency | 50/60 Hz |
Packaging Type | Packet |
Specialities | Rugged Construction |
Type | Enclosure Heaters |
Shape | Round |
Finishing | Coated |
Preferred Buyer From
Location | Worldwide |
Heatcon flameproof heaters are usually supplied with enclosures certified by certain agencies and can be used in ail applications where flameproof enclosure is needed:-
Features :
SHEATH MATERIAL:-
Typical Applications
Business Type | Manufacturer, Supplier |
Standard Dimensions | (@ 6,5 mm and 8,5 mm) as well as in square shape (6 x 6 mm and 8x 8&mm) |
Sheath | SS & Nickel |
Terminal | M2.5 ,M4 |
SS Lengths | Minimum 300 & Maximum 3000mm (SS) |
Nickel Lengths | Minimum 350 & Maximum 2000mm (Nickel) |
Preferred Buyer From
Location | Worldwide |
The Flexible tubular heater can be manually bent and this bending of the makes it easy to handle, simple to assemble. Available in different lengths.
Main Features :-
Business Type | Manufacturer, Supplier |
Features | Compact Design, Easy to Install, High Power Output, Long Service Life, Light Weight , Customized Design |
Material | Metal |
Color | Grey |
Shape | Rectangular |
Usage | Industrial |
Power Source | Electric |
Preferred Buyer From
Location | Worldwide |
HEATCON heater bank it is possible to heat air or gases up to 800°C and maintain a uniform temperature throughout the room or chamber. Installation is very simple and efficient.
INSTALLATION:-
Typical applications:-
Business Type | Manufacturer, Supplier |
Outer Sheath | Ss 304/incoly/inconel 600/ss 310/ss 321/55316/brass |
Resistance Wire | Nichrome 80/20 |
Pins | 100 % Pure Nickel |
Insulation | MGO |
Sealing | Cement/ Silicon/ Teflon |
Lead Wires | Teflon/SS Braided/Fibre Glass Insulated |
Standard Diameters | 6.5,8,9.5,10,12.5,16,19,20,22,25mm |
Tolerance in Diameter | -0.05mm |
Length | 30mm-1500mm |
Tolerance in Length | ± 1.5% |
Min Max Voltage | 480V |
Wattage tolerance | ±10% |
Preferred Buyer From
Location | Worldwide |
HEATCON High Density Cartridge Heaters is manufactured using the best materials and construction methods. Extensive Quality & Testing throughout the production process assures the continuous and superior performance of the heaters.
The swaged assembly produces a highly compacted heater that will have the ability for maximum element life & uniform heat transfer. These heaters last up to 10 times longer than normal un-compacted cartridge heaters.
Cartridge heater compacted by magnesium oxide offers high performance. With a maximum rating Wattage upto 70 Watts/Square inch & Temperature up to 750° degree centigrade on the sheath of the heater.
Applications :
Business Type | Manufacturer, Supplier |
Usage | Used in the Process Industry for Heating Liquids , Heating Gases and as Tank Heaters |
Material | Metal |
Power Source | Electric |
Finish | Coated |
Feature | Easy to Use |
Preferred Buyer From
Location | Worldwide |
These type of immersion heaters are mostly used in the process industry for heating liquids , heating gases and as tank heaters. Immersion heaters are tubular welded or brazed into a flange. The enclosure can be selected depending upon the applications and can be customized with ANSI standards flanges.
Business Type | Manufacturer, Supplier |
Element Wire Material | Nichrome, 80-20 |
Surface Wattage | 20-25 W/In2 |
Heater Tube Sizes | @ 8,11,14 mm |
Grade of Protection for Enclosure | Ip 55, Ip 65, Ip 67, Atex, Ccoe, Flameproof |
Type of Termination | Threaded, Cable |
Connectors | Industrial Sockets or Special Connectors from Amphenol Connectors (on Request) |
Sheaths | SS 304, SS 316, SS 310, Inconel 600, Inconel 800, Titanium, Inconel |
Preferred Buyer From
Location | Worldwide |
Teflon coated heaters are mostly used in the process industry for heating harsh liquids & chemicals.
These heaters are similar to Immersion heaters as tubular heater is welded or brazed into a flange or threads and then the Teflon is coated on to the tubes to resist the tube from corrosion of chemicals.
Business Type | Manufacturer, Supplier |
Element Wire Material | Nichrome, Kanthal |
Surface Wattage | :41 - 47 W/Ina |
Heater Tube Sizes | 0 8,11,14 mm |
Grade of Protection for Enclosure | IP 55, IP 65, IP 67, Atex, Ccoe, Flameproof |
Type of Termination | Threaded, Cable |
Connectors | Industrial Sockets or Special Connectors from Amphenol Connectors On Request |
Sheaths | Ss 304, Ss 316, Ss 310„ Inconel 600 , Inconel 800, Titanium, Inconel |
Preferred Buyer From
Location | Worldwide |
Heatcon the versatile and economical tubular heating element lends itself to virtually the entire range of below applications:-
Tubular heating elements have a variety of mounting and termination options making them highly popular among industrial customers.
Hi! Simply click below and type your query.
Our experts will reply you very soon.